The 36/600 has an appearance similar to the Marblehead yachts. This development class is restricted in overall length and sail area. While these yachts are commercially available, their simplicity also makes them a good choice for beginning builders. 36" long, 600 sq. inches sail area.

The 36/600 is one of the largest classes certified by AMYA, with nearly 1500 boats registered since its introduction in 1971. Some of the contributing factors for the 36/600's national popularity is that they are economical to build, easily transported, and a genuine pleasure to sail.

The 36/600 is a developmental class, so there are very few restrictions beyond the thirty-six inch hull length and six hundred square inches of sail area. The class specifications are so worded to encourage the designers and builders to fully utilize their imaginations. Design diversity for 36/600 hulls is quite broad. For example, beams range from a narrow five inches to over eight inches. Sail aspects range from forty-five inch luffs to over sixty inch luffs. The weight of a 36/600 can vary from under five pounds to over eight pounds. Though there is usually a commonality of boats sailed by a club, it isn't unusual to have most of the boats quite different in design. This gives a skipper the option of exercising their judgment of which design is best for the the prevailing conditions at their sailing venue.

The sailing characteristics of the 36/600 are well suited for both the experienced skippers and the beginner. For a novice skipper, the 36/600's size and simplicity makes understanding the boat and what makes it go quite easy. For the veteran skipper, the quick response and "on the edge" speed makes the 36/600 an ideal choice for competitive sailing.

The DragonFlite 95 is a Restricted One Design boat that is meant to compete within a strict set of rules to ensure a true test of a skipper.s ability to tune their boat and race it well.

The DragonFlite 95 is a Restricted One Design boat that is meant to compete within a strict set of rules to ensure a true test of a skipper's ability to tune their boat and race it well. Additionally, this 950mm boat is of high quality for a modest price. The DF95 is sold ready to race which includes transmitter and receiver, just add AA batteries. For those already in the hobby, a boat without transmitter and receiver can be purchased. The DF95 comes with a carbon fiber keel, Mylar sails, and a one piece carbon mast, all cutting edge components. It can be on the water in a few hours and assembled by a person with no experience building boats.

One Design Sanctioned in 1995. Also called "One Design One Meter". The ODOM is based on a U.S. One Meter design. This small-sized yacht's kit must be initially purchased from the manufacturer. Sails are strictly controlled, but may be purchased or made from scratch. This one design class allows no variations. The class is managed by a class association. 39.37" long.

Odom is a One Design Class. See the Class Rules for specifications. Length 39 3/8". Weight 7 1/4 lbs. height bottom of bulb to masthead 75". Comes in 12 hull colors. Minimum construction time. Good entry level boat. Handles strong puffs, choppy water, and points well.

The RG-65 is an International development class with a 30 year history. The class rules limit only the length of the hull (65 cm), the height of the rig (110 cm) and the sail area (2250 square centimeters) 650mm long.

Sanctioned in 1993. The Soling 1 Meter is based on the full-size Olympic Soling. Specifications: 39.37" long, 8-5/8" beam, approx. 60" bottom keel to tip of mast. 10 lbs. min.
Features: Performance; Single rig allowed means lower total cost; One Design for equality of boats; Kit-Based, kits Available from two manufacturers; Wide distribution of local clubs in all AMYA Regions.

The Soling 1 Meter Class was first sanctioned by the AMYA in 1993. With thousands of kits sold, and some 4000 boats registered, you can find a Club sailing the Soling 1 Meter in ALL 8 AMYA Regions, and three Provinces in Canada. Over 70 USA and Canadian Clubs list the Soling 1 Meter as the one or the only boat that they support. Something like 50% of ALL RC sailors own at least one Soling!! For over thirty years since being AMYA-sanctioned, the "Soling" has been a Class that offered top competition at the local, Regional, and USA as well as Canadian National Championship levels.
The Soling 1 Meter is a true One-Design: All aspects related to performance are intended to be restricted to what can be achieved by building a Kit straight from the manufacturer's instructions. (The Soling 1 Meter Class Rules may be downloaded from the links table on this page.)
Performance: Soling 1 Meters point high, sail fast, and resist "submarining" like some other more narrow and lighter boats. On a fresh reach or run, the boat gives her skipper fully controlled, exhilarating performance. The fin keel draws only about 8" of water, so the Soling 1 Meter is easier to carry and transport, and can be launched from a shore without wading, as well as from a dock. And, the Soling resists snagging in pond weeds - she can almost always be sailed back to shore, instead of having to be rescued by rowboat.
Low total cost: Unlike many RC boats, Soling 1 Meter Class allows one rig, using lower cost flat-paneled polyester sails. The Soling can be sailed in winds from near zero to over 20 MPH, using that single rig. And, in a regatta of less than 5 days' duration, you must use the same rig throughout the regatta. This saves hundreds of dollars for additional rigs and sails required to be bought in order to compete in most other popular designs.
Soling 1 Meters must be built from a kit available from the original manufacturer- Victor Model Products (out of business as of 2018), AND currently only from one of two Class-approved manufacturers:
3DRC Boats offers Almost ready to Sail kits that can be finished in about 12 hours by virtually anyone. 3DRC also sells full rig kits, aluminum mast and booms, with or without major brand sails.
Vac-U- Boats offers an unassembled hull kit.

You cannot modify the interior construction of the 3DRC or Vac-U-Boat kits, such as removing structure, or adding carbon fiber or other "exotic" materials.
Made in the USA: All Solings, since the first off the mold, have been made in the USA.
To buy a NEW Soling, contact one or both of our manufacturers:
3RC Boats TM
sales@3drcboats.com
Doug Rieger
1-440-610-9542
http://3drcboats.com
OR
Vac-U-BoatTM
philpace@vac-u-boat.com
Phil Pace
1259 Humphries Rd. Conyers, GA 30012
http://www.vac-u-boat.com/

The Soling 50 is based on the full-size Olympic Soling. This medium-sized yacht's hull must be initially purchased from a manufacturer (See Class Page). Decks, keels, rigging, spars and sails are strictly controlled, but may be purchased or made from scratch. Almost all other equipment is up to the owner. 50" long.